Glue RS100 (22L)
Price
€209.00
Delivery 3-5 working days.
The contact adhesive is resistant to water and hot temperatures.
The adhesive is suitable for most wood sheet...
Delivery 3-5 working days.
Contact adhesive for bonding wood, chipboard, MDF, DTD, polyurethane foam, fiberglass, laminate, cardboard, aluminum sheets and most metals.
Due to the high content of dry residue (28-32%), they ensure high and reliable strength of the glued joint. Pressure-applied glue is easy to spray, colorless, heat-resistant up to 85 °C.
Application: Spray glue on both surfaces to be glued, which must be dry, dust-free and clean. The recommended room temperature is 15-25 °C, the glue is sprayed at a distance of 15-25 cm from the surfaces to be glued. Ideally, the surfaces will stick together if you cover 80-100% of the surface with a thin and even layer of glue. The surface should look like it is covered with a fine mesh, do not apply a thick layer, as excess glue may spill over the sides. After spraying the adhesive on the surfaces to be bonded, allow the thinner to dry for 30-60 seconds. Then firmly press the surfaces to be glued together. If the surfaces are difficult to absorb, then spray a second layer of glue and repeat the procedure.
For full use, purchase a hose and spray gun.
Contact adhesive for bonding wood, chipboard, MDF, DTD, polyurethane foam, fiberglass, laminate, cardboard, aluminum sheets and most metals.
Due to the high content of dry residue (28-32%), they ensure high and reliable strength of the glued joint. Pressure-applied glue is easy to spray, colorless, heat-resistant up to 85 °C.
Application: Spray glue on both surfaces to be glued, which must be dry, dust-free and clean. The recommended room temperature is 15-25 °C, the glue is sprayed at a distance of 15-25 cm from the surfaces to be glued. Ideally, the surfaces will stick together if you cover 80-100% of the surface with a thin and even layer of glue. The surface should look like it is covered with a fine mesh, do not apply a thick layer, as excess glue may spill over the sides. After spraying the adhesive on the surfaces to be bonded, allow the thinner to dry for 30-60 seconds. Then firmly press the surfaces to be glued together. If the surfaces are difficult to absorb, then spray a second layer of glue and repeat the procedure.
For full use, purchase a hose and spray gun.
Glue RS200 (22L)
€265.00
Tax included
Delivery 3-5 working days.
Contact adhesive for bonding wood, chipboard, MDF, DTD, polyurethane foam, fiberglass, laminate, cardboard, aluminum sheets and most metals.
Due to the high content of dry residue (28-32%), they ensure high and reliable strength of the glued joint. Pressure-applied glue is easy to spray, colorless, heat-resistant up to 85 °C.
Application: Spray glue on both surfaces to be glued, which must be dry, dust-free and clean. The recommended room temperature is 15-25 °C, the glue is sprayed at a distance of 15-25 cm from the surfaces to be glued. Ideally, the surfaces will stick together if you cover 80-100% of the surface with a thin and even layer of glue. The surface should look like it is covered with a fine mesh, do not apply a thick layer, as excess glue may spill over the sides. After spraying the adhesive on the surfaces to be bonded, allow the thinner to dry for 30-60 seconds. Then firmly press the surfaces to be glued together. If the surfaces are difficult to absorb, then spray a second layer of glue and repeat the procedure.
For full use, purchase a hose and spray gun.
Contact adhesive for bonding wood, chipboard, MDF, DTD, polyurethane foam, fiberglass, laminate, cardboard, aluminum sheets and most metals.
Due to the high content of dry residue (28-32%), they ensure high and reliable strength of the glued joint. Pressure-applied glue is easy to spray, colorless, heat-resistant up to 85 °C.
Application: Spray glue on both surfaces to be glued, which must be dry, dust-free and clean. The recommended room temperature is 15-25 °C, the glue is sprayed at a distance of 15-25 cm from the surfaces to be glued. Ideally, the surfaces will stick together if you cover 80-100% of the surface with a thin and even layer of glue. The surface should look like it is covered with a fine mesh, do not apply a thick layer, as excess glue may spill over the sides. After spraying the adhesive on the surfaces to be bonded, allow the thinner to dry for 30-60 seconds. Then firmly press the surfaces to be glued together. If the surfaces are difficult to absorb, then spray a second layer of glue and repeat the procedure.
For full use, purchase a hose and spray gun.
You have questions about Glue RS200 (22L) ?
Our specialists will consult and answer your questions.
Ask question
Our specialists will consult and answer your questions.
Ask question
Saugus Atsiskaitymas
El. Bankininkystė, Grynais arba Visa - Mastercard
Nemokamas Pristatymas
Nemokamas pristatymas užsakymams nuo 59€.
Nemokamas Grąžinimas
Suteikiame 14 dienų pinigų grąžinio garantiją
Product photos are for illustrative purposes only, the original products may differ slightly from those shown in the online store.
30101879
3 Items
Specific References
New product
You might also like
Related Products ( 3 other products in the same category )
- -10.03%